Knowledge Base Articles
Welcome to UTEX Scientific support, your technical resource gateway. You can search all support resources or concentrate on a particular product or area.

Show resources for a specific product:
Show only specific category:
Show: All   Downloads   Knowledge Base   White Papers   Product Documentation
Search Knowledge Base Articles for:
Entries 1 to 23 of 23
ResourcePublished
Tecnatom SONIA FPR8A Module
» Support » Knowledge Base » Hardware Support
2016/04/19
03:46:40 PM
The UTEX Motion Pendant
» Support » Knowledge Base » Application Notes
2014/12/29
07:34:30 AM
Windows Upgrade Assessment
Windows Upgrade Assessment to help you assess the future of your Windows XP-based UTEX inspection system.
» Support » Knowledge Base » Hardware Support
2014/10/23
10:47:59 AM
Utex Windows XP Support Notice
Your UTEX system PC is an industrial controller that hosts specialized components for motion control and high speed data acquisition. It should not be upgraded before contacting UTEX technical support for advice.
» Support » Knowledge Base » Hardware Support
2014/10/23
10:43:56 AM
How to use the SP1 and SP0 commands to turn a UT340 ON and OFF
This article describes how to control the UT340's low voltage power supply power, using the SP1 and SP0 commands sent via RS232 interface. Also described is the method for recovering from an error state.
» Support » Knowledge Base » Hardware Support
2012/11/19
08:05:34 PM
Resolving Winspect time-out error for Galil DMC 18xx motion controllers
Winspect 5.5 and 6.x scanning systems using Galil DMC 18xx controllers may report a time-out error from the Galil motion controller during scanning. This note describes how to configure the Galil DMC drivers to eliminate the problem.
» Support » Knowledge Base » Hardware Support
2012/08/13
12:35:46 PM
InspectionWare maintained build downloads
InspectionWare builds maintained for specific customers.
» Support » Knowledge Base » Software Support
2012/04/24
02:17:49 PM
Customizing motion axis behaviour under manual control
This note describes how to use some of InspectionWare's features to customize how a machine behaves when it is under manual control. Examples include settings for motion with incremental speeds or fixed speeds, and how to configur the behaviour of the user controls to command motion for only as as long as the control button is depressed.
» Support » Knowledge Base » Application Notes
2012/03/15
06:38:49 PM
NI USB-6008 used with EC Instrument
Most of Eddy current instruments can output its real and imaginary data via two analog outputs. Using a simple A/D device such as NI USB-6008, one can easily interface an Eddy Current instrument in InspectionWare
» Support » Knowledge Base » Hardware Support
2012/02/01
12:05:28 PM
TOF Peak Interpolation for Precise Distance Measurements
You don't always need the world's fastest digitizer to get excellent distance resolution.
» Support » Knowledge Base » Application Notes
2011/11/13
02:18:49 PM
Hardware Drivers for Winspect 6.x versions
This article lists the appropriate drivers for popular motion control and instruments hardware running under Winspect 6.x and Windows XP operating systems.
» Support » Knowledge Base » Hardware Support
2010/12/23
05:04:27 PM
How to run Winspect and InspectionWare on the same computer
This document describes how to setup your workstation to run Winspect and InspectionWare on the same computer.
» Support » Knowledge Base » Application Notes
2009/10/14
02:10:10 PM
How to perform a Master Reset on UT320 and UT340 Instruments
UT320 and UT340 instruments can be returned to factory default specifications by performing a master reset. This document describes the procedure for each type of instrument.
» Support » Knowledge Base » Hardware Support
2009/09/14
04:55:30 PM
Controlling UT320 and UT340 Instruments from your own software
The UT320 and UT340 instruments can be controlled remotely by simple ASCII commands, communicated through a standard RS232 serial port.
» Support » Knowledge Base » Application Notes
2009/09/10
03:44:12 PM
Installing Imagine3D on an XP based machine
» Support » Knowledge Base » Application Notes
2008/01/23
03:39:38 PM
Assembly Diagram for NI 6601 Cable Assembly (UTEX Part # AY13-072-001)
» Support » Knowledge Base » Application Notes
2008/01/23
03:18:40 PM
Backing Up the Winspect System
It is a good practice to back up your Winspect system on a regular basis. This protects you against accidental file deletions, and against computer-related disaster, such as hard-drive failures, water or fire damage, and so on...
» Support » Knowledge Base » Application Notes
2008/01/23
01:29:02 PM
Using Phoenix Contact Optima MD/100 Interconnect Modules
The Phoenix Contact Optima MD/100 module provides a convenient field termination for motion control signals that are interfaced to a Galil motion control card, such as the DMC 1700 and DMC 1800 series...
» Support » Knowledge Base » Application Notes
2008/01/23
01:10:46 PM
Ways to to use motor controllers and encoder interface cards for scanning
Winspect and InspectionWare can be configured in many different ways to collect NDT data.
» Support » Knowledge Base » Application Notes
2008/01/23
01:03:25 PM
Adding a pre-trigger enable output to the Sonix STR81G digitizer
Instruments with uncertain trigger timing -- Some ultrasonic systems when externally triggered are not immediately able to generate their main output pulse. These systems include flaw detectors with trigger jitter, multiplexers that need to first switch to the next channel and EMAT systems that first need to build up energy....
» Support » Knowledge Base » Application Notes
2008/01/23
11:21:07 AM
Adding a pre-trigger enable output to the Sonix STR8100 digitizer
Instruments with uncertain trigger timing -- Some ultrasonic systems when externally triggered are not immediately able to generate their main output pulse...
» Support » Knowledge Base » Application Notes
2008/01/23
11:12:31 AM
Connecting UT320 and 340 Pulser Receivers
Connecting UT320 and 340 Pulser Receivers to external hardware such as scopes, digitizers, trigger sources
» Support » Knowledge Base » Application Notes
2008/01/18
03:51:07 PM
Manual Scanning Modes
An illustrated guide to manual scanning modes supported by Winspect and InspectionWare
» Support » Knowledge Base » Application Notes
2007/12/07
02:54:17 PM
 
  Print Email page Share